How To Repair A Wind Up Clock

Clock Repair

Along with being dealers in some of the most sophisticated clocks and timepieces from around the world, nosotros likewise agree the distinction for being an authorized service center for some of the leading clock manufacturers, such as Howard Miller, Ridgeway and Sligh. This means that our customers receive not only the all-time in customer service just continuing technical service support on many clocks purchased from us. Non just tin can nosotros service many warranty issues for our customers but our Wisconsin clock shop also offers clock repair for the general public, including antiquarian clocks. Nosotros accept outlined a guide for some common troubleshooting problems with new clocks below.

What if my mechanical clocks will non operate?

Ensure that all of the packing cloth has been removed. If the clocks are a pendulum type, ensure that the spring clip or rubber band has been removed from the back of the movement. Endeavour re-starting your clocks. For pendulum clocks, information technology is important to give the pendulum a full swing. Is the pendulum hitting the weights? If so, check the stability and level of the clocks. Practice the easily operate without interference? Practise not let the hour hand striking the second hand. If the second hand is rubbing the dial, pull it out slightly. If the 60 minutes paw is rubbing against the back of the minute hand, the hour hand should be pushed closer to the dial. Did you bank check the break bound? If information technology is non hanging straight down, loosen the thumbscrew and straighten the pause spring. Retighten the thumbscrew.

Ensure that the verge pivot is properly located in the slots of the pendulum guide. For weight-driven clocks, make certain that the weights are in their proper location. The proper position of the weights as you are facing the clock is labeled on the bottom of each weight. Ensure that the clocks are wound and the weights are up.

If the clocks have a moving moon, ensure that the moon is non caught on the click spring. If the clocks are cablevision-driven and were previously run or the white styrofoam blocks were removed from the cablevision pulleys, it is possible that the cables were wound upwards without weights left on the caster. Equally a result, the cable(s) have overlapped on the drum(s). Check each cable on each pulsate to come across if it is overlapped. Is so, attempt to correct the cables so that they are not overlapped. Correcting this problem is not covered under the warranty.

What if my mechanical clocks do non strike the correct hour?

If the clocks are new, permit them to operate for several hours before making any adjustments. If the strike is off, grasp the 60 minutes Manus ONLY and rotate it frontwards or backward to line up with the correct 60 minutes on the dial indicated by the number of times the hr strikes. Rotating this hand independently will not harm the motility. Then adjust the hands to the right fourth dimension past rotating the infinitesimal hand CLOCKWISE. Exercise Non MOVE THE Hands WHILE THE CLOCKS ARE CHIMING OR STRIKING. After a few hours, the move's self-adjusting feature will synchronize the hands with the correct chime and strike.

What if my mechanical clocks volition not chime or strike?

Make sure that the strike on/off lever is not in the "strike off" position or halfway between positions. Make sure that the move is not in the "dark off" position. Make sure that all the packing material is removed from the motion area. You should exist able to advisedly pull each hammer back abroad from the rod approximately 1 inch. Check the hammer aligning to be sure that the hammers are properly aligned with the gong rods.

For weight-driven clocks, make certain that the weights are in their proper location. The proper position of the weights equally y'all are facing the clock is labeled on the bottom of each weight. If your clocks are cable-driven clocks and were previously run, it is possible that the cables were not wound upwards with the weights left on the pulley. When this happens, the cables overlap on the drum. Check the cables on the drums to run into if they are overlapped. Correcting this trouble is not covered nether the warranty.

What if my mechanical weight-driven chimes/hour strikes seem uncommonly fast or slow?

Be certain that the weights are in their proper location. The proper position of the weights as you are facing your clock is labeled on the bottom of each weight.

What if my mechanical clocks are in the "night off" position and it is silent during the day instead of the night?

Rotate the minute hand clockwise twelve hours. Do NOT MOVE THE HANDS WHILE THE CLOCKS ARE CHIMING OR Striking.

What if my clock chimes have the incorrect tone?

Do NOT Suit THE CHIME HAMMER, unless the chime tone is wrong. The chime tone may be affected by the hammer resting on the chime rod (coil) or striking the rod (coil) off center. Although the hammers were gear up at the manufactory, it is possible for the hammers to get out of adjustment. Chime hammer arms are made of brass and can be aptitude safely. This is achieved by angle the hammer arms slightly in the middle and then that the hammers rest approximately one/viii inch from the chinkle rod. DO Non bend the chime rod.

What if my pendulum hangs crooked or hits the weights?

Pendulums can easily get twisted by improper handling. To straighten the pendulum, get-go remove it from the clock. Use cotton gloves or a soft non-abrasive material when treatment the pendulum. With one hand, concur the pendulum beneath the height strap. With the other hand, grasp the pendulum bob. Gently twist the pendulum in the direction necessary to eliminate the twist.

What if the hands get aptitude?

Clock hands are easily bent. Carefully curve them back to the correct position.

How do I reset the time for daylight savings?

Accelerate the minute hand clockwise until the right time is set. When moving the hand forward, it is important to permit the clocks to chime every quarter 60 minutes (1/iv, 1/2, 3/iv, 1) before advancing the hands to the adjacent quarter hour position. DO NOT Motility THE Hands WHILE THE CLOCKS ARE CHIMING OR STRIKING.

How do I wind my clocks?

Floor Clocks (cables with pulleys): weights that are suspended by cables with pulleys should be raised using the crank provided. DO NOT lift the weights by hand while cranking. Insert the crank into the holes located in the dial face. It does non matter in what gild the clock weights wind. All weights demand to be wound to the upward position.

Wall and Mantel Clocks: Insert the winding key into the holes located in the dial face. Depending upon the model of the clock, in that location can be 1, 2 or 3 winding holes. Turn the key clockwise until the jump becomes tight and will not plow further. For clocks with hanging weights, enhance the weights using the crank. DO NOT elevator the weights by paw while cranking. Wind these clocks one time a calendar week. Information technology does not matter in what order the clock weights are wound. All springs must be fully wound.

What if the weights exercise not drop at the same rate?

When the automatic night shut-off characteristic is selected, and on some models when "silent" is selected, the center weight will drop at a faster rate than the other weights.

How should I prepare to move floor clocks?

Care should exist taken whenever you move your clocks to ensure that all accessory parts, such every bit weights, pendulum, ect., are removed and packed properly to prevent damage. Use cotton gloves or a soft cloth when handling the pendulum or weights. For clocks with a cable-driven movement, air current the weights all the way upwards. For clocks with chains, employ a long wire or string and put it through the chain links but beneath the chain sprocket. When done properly, the wire or string should go through vi chain links. Secure the wire or string to prevent the chains from coming loose from the sprocket. Advisedly finish the pendulum from swinging. Remove the weights. NEVER current of air the clocks without the weights installed. For clocks with bondage, secure the chains so that they do not harm the finish. Next, remove the pendulum. For tubular movements, remove the tubes. Go along the clocks in an upright position while carefully moving it to its new location. Ensure that the pulleys are properly located on the cables and the chains are properly located on the sprockets.

What is meant by "triple chinkle" clocks?

Triple chime refers to clocks that play a choice of iii different melodies. The almost common triple chime melodies are Westminster, St. Michaels and Whittington.

What is the proper function of the moon dial?

When properly fix, the moon dial tracks the lunar month and cycle of the full moon.

What if my quartz dual chime move will not operate properly?

Starting time, ensure that brand new alkaline batteries are in place. Batteries made by diverse manufacturers may present some difficulty in working properly in the movement. A poor electrical connexion tin can cause inferior functioning. Ensure that the positive battery contacts are positioned over the nub on the terminate of the battery. The problem area is typically the negative end of the battery. Ensure that the negative battery contacts are positioned completely on the metallic contact area of the battery.

Where is our Wisconsin clock repair shop located?

Our Wisconsin clock repair shop is located in Merton at W282 N7137 Main St.. Surrounding communities for clock repair include Waukesha, Milwaukee, Pewaukee and Oconomowoc. Nosotros are a member of the National Scout Association of Watch and Clock Collectors.

Other problems and remedies:

Pendulum will non swing: To provide proper pendulum performance, information technology is besides necessary to ensure that the clocks are level. Likewise check that the pendulum is properly located on the pendulum hanger and that the speaker wires are non interfering with the pendulum operation in quartz models.

Chinkle volume is off or lower during the day and louder at other times: The nighttime volume reduction or shut-off is not properly fix. Reset the nighttime close-off.

Chime is off/will not chime: Ensure that the chime is not in the "OFF" position. If this does not solve the problem, supercede the batteries.

The clock chimes several minutes before the hr when the hands are moved manually: This is normal. The clocks will chime on the hour under normal operation.

Source: https://www.giftoftimeclocks.com/clock-repair.html

Posted by: bockbutragreake.blogspot.com

Share this post